Remember that beautiful Restoration Hardware-inspired coffee table I built for my parents? Well, it was such an easy project and I loved it so much that I decided to make one for our living room! The folks at Osborne Wood were kind enough to send me another set of the turned legs they designed for this coffee table! The legs are custom, but are available for sale here!
I modified Ana White’s plans so that our table would fit more appropriately in our space. I like to think of ours as the baby brother of the original Balustrade coffee table. We needed ours to be more square-ish (it’s a word, don’t judge), so it had to be a bit shorter, but wider at 49-1/2″ long by 38-1/2″ wide. This meant my shopping and cut lists had to be adjusted, of course.
Here are my modifications:
- 5 – 1x6x8
- 4 – 2x4x8
- 5 – 2x6x8
- 1 – 1×4 @ 15″ long
- 4 – turned legs (Osborne Wood #1332)
- 1-1/4″ and 2-1/2″ pocket hole screws
- 2″ or longer wood screws
- 9 – 1×6 @ 38-1/2″ (bottom shelf)
- 2 – 2×4 @ 49-1/2″ (bottom frame)
- 2 – 2×4 @ 30″ (bottom frame – may need to cut to fit)
- 4 – 1×4 @ 3-1/2″ (feet)
- 8 – 2×6 @ 5-1/2″ (blocks on each leg)
- 2 – 2×4 @ 36-1/2″ (long aprons – may need to cut to fit)
- 2 – 2×4 @ 25-1/2″ (short aprons – may need to cut to fit)
- 7 – 2×6 @ 38-1/2″ (top shelf)
- 2 – 2×6 @ 38-1/2″ (breadboard ends – may need to cut to fit)
I won’t write up a long, detailed tutorial because that one already exists, so here’s a quick run-down:
I like to cut as I go along, so my measurements are more precise and there is no wasted lumber. I cut nine of the 1×6 boards to 38-1/2″ long and then assembled them with pocket hole screws underneath. Next, I measured the long side of the bottom shelf (49-1/2″), cut two 2×4 boards to fit, and attached them to the underside of the bottom shelf. Then I measured the space along the short side of the bottom shelf and cut two 2×4 boards to fit (30″) and attached those to the underside of the bottom shelf as well, to create a frame under the bottom shelf.
After that, I attached a 3-1/2″ square “foot” to each corner of the frame. Then I moved onto assembling the legs and attached them to the bottom shelf, 1″ inset from the edges. Because there are plenty of variables that decide how long the aprons will be, I measured the space between each leg and cut an apron to fit. I ended up cutting four different aprons for each side. The long aprons measured 36-3/4″ and 36-7/8″ and the short aprons measured 25-3/4″ and 25-5/8″. I attached them to the legs with pocket holes.
I assembled the table top in the same manner as the bottom shelf then attached it to the aprons and legs with wood screws and glue. For a more thorough tutorial, check out Ana’s original plans here.
And once again, I’ll never stop singing praises to the mighty belt sander. It’s responsible for my flat-as-can-be tabletop. Love it! After sanding the top and bottom shelf down so that everything was all flush and level, I followed up with my palm sander fitted with 150- and 220-grit sandpaper.
Then for the stain, I layered Minwax’s Special Walnut over their new color, Weathered Oak, and finished it using their Wipe-On Poly (amazing stuff!). I applied 3 coats total, sanding in between coats, wrapping a sheet of 400-grit sandpaper around a scrap block of wood and sanding the table top and bottom shelf by hand, before wiping on each coat. I’m telling you guys, this Wipe-On poly stuff is the jam. It’s so easy to apply and you don’t have to worry about drips, brush strokes, or bubbles! And it provides enough protection for these occasional tables, that I am smitten. Ah-mah-zink.
For anyone who’s timid about building furniture from scratch, this is YOUR project. It’s the perfect beginner-level build. Don’t forget! Go here for the complete, step-by-step plans. Also, you can check out the original Restoration Hardware-inspired Balustrade Coffee Table, where you’ll find a ton more work-in-progress photos and a few helpful tips.
Feel free to pin and share this project! Thanks for reading, friends!
Miss Mustard Seed