*This project is sponsored by The Home Depot.
My Oh My! I’ve had ants in my pants over this DIY Sliding Barn Door Loft Bed project for months now and I am SO EXCITED to finally share the plans and tutorial with you guys! Are you ready for this? Hunker down, friends, this is gonna be one ton of fun.
If you follow me on Instagram, you’ll have seen sneak peeks and behind-the-scenes footage as we were building this DIY sliding barn door loft bed. I saved the Instagram stories in my highlights, so feel free to check that out. By the way – this plan fits a full-size mattress and the total cost was about $550.00. Also, just for reference, we have 9-foot ceilings in this room.
Do you want the cliff notes? Here’s how it’s gonna all shake out… and if you’re curious about the basics of staining and finishing wood, watch the videos at the end of this post!
- Railings
- Side panels
- Front and back panels
- Mattress box
- Assembly
- Stairs
- Doors
- Roof
Hardware and Roofing Supplies:
- (1) Sliding Barn Door Hardware Set
- (2) Top Mount Hangers
- (6) Simpson Strong-Tie Fence Brackets
- (8) 3/8-inch x 5 1/2-inch Carriage Bolts
- (3) 3/8-inch Split Locking Washers 3-pack
- (1) 3/8-inch Zinc-Plated Steel Flat Washers 8-pack
- (4) 3/8-inch Zinc-Plated Cap Nuts 2-pack
- (3) Suntop 26-inch x 8 ft. Polycarbonate Corrugated Roof Panels in Castle Grey
- (1) Suntop 4-ft. Ridge Cap in Castle Grey
- (1) Woodtite 1-inch Fasteners 50 pcs.
- 2 1/2-inch and 1 1/4-inch Wood Screws
- 2 1/2-inch and 1 1/4-inch Pocket Screws
- 1 1/4-inch Brad Nails
How to build a DIY Sliding Barn Door Loft Bed
1. BUILD THE RAILINGS
You can purchase 2×2 lumber off-the-shelf, but we found it to be more cost-effective to rip down 2×4 studs to make the 2×2 balusters. We used a 2×4 spacer to evenly space the balusters 3 1/2 inches apart. Pre-drill pilot holes and countersink the 2 1/2-inch wood screws. It’s also a good idea to sand the balusters before you attach them.
Lather, rinse, repeat eleventy times.
Fill the screw holes with wood filler, then sand smooth.
2. BUILD THE SIDE PANELS
Does your Home Depot sell 2×3 lumber? My Texas store location does, but I could never find them when we lived in Alabama. If you can get your hands on some 2x3s, they’ll work best because they allow the tongue-and-groove boards to be slightly inset. In the photo below, the rails are 2x4s and the stiles are 2x3s. See the inset? Now you’ll be able to attach the 3/4-inch thick T&G boards and not have them stick out past the 2x4s.
Notice how the T&G boards fit nicely into place. Once you build the frame, you’ll just glue and nail the T&G boards in place – easy peasy.
The photo below shows one constructed side panel. You’ll build two of these, of course. These will end up being the headboard and footboard of the bed.
Special shoutout to my good friend and neighbor, Tamra. She’s a supermom to 6 kids (3 of which are triplets!), Army wife, and overall amazing friend. She’s been a Godsend. Tamra’s not only listened to me over-analyze, second-guess, and agonize over every part of this project, but she helped me sand and paint ALL THE THINGS. And there were so many things to be sanded and painted. She’s a trooper. Thank you, Tamra!
I built each component (railings, side panels, front and back panels, mattress box) separately, then brought everything into the room for assembly, but I’d recommend building as you go, if you can. No matter how accurate my measurements were, once Adam and I got the parts into the room, those pre-determined measurements changed and shifted as we put the bed together. So, if you can (and if you have the patience and time), build as you go. Meaning, build the two side panels and back railing, then take the completed side panels into the room, then attach the back railing. The side railings are permanently attached, while the back railing slides into place with these fence brackets. This makes disassembly much easier when it comes time to PCS (move). Measure the space for the mattress box, then build accordingly. Attach the mattress box to the legs, then measure the space for the front and back panels, then build for those dimensions… and so on and so forth. Make sense?
Because I built the side, front, and back panels beforehand, then tried to put it all together in the room, there was a lot of trial and error. We’d carry the front panel into the room, try to fit it into position, discovered it wouldn’t fit, then have to take it back out to the shop to shave the sides down with a hand planer and belt sander until the front panel fit into place. Same thing goes for the back panel.
My sweet husband. He lifts all the heavy things. Repeatedly. God bless him.
If you build as you go, you’ll be able to measure and then build to those measurements. If you choose to build the loft bed the way I did, just know that you’ll likely need to make adjustments along the way. I hope you have a sweet husband who lifts heavy things repeatedly too.
3. BUILD THE FRONT AND BACK PANELS
Same song and dance for this part too – the stiles are 2x3s while the rails are 2x4s, which allows space for the tongue-and-groove boards to be slightly inset from the 2×4 rail. Attach the T&G boards with glue and nails.
For the windows, I constructed the outer frame with pocket hole joinery and cut overlap joints for the muntins (the criss-cross part). The muntins were then attached to the frame with pocket screws. I cut the lap joints with several passes on the table saw. You can also use a circular saw for this – just be sure to set the depth of the cut so that you’re removing half the amount of material on both pieces so that when you join the two, you’ll have a flush surface.
4. BUILD THE MATTRESS BOX
This part is pretty easy. First, you’ll build the box out of 2x6s and 2 1/2-inch wood screws. Check for square, adjust as necessary.
Next, you’ll attach the 2×3 mattress cleats to the sides of the bed box. Measure and mark the center point on the short ends and attach the fence brackets. These brackets will hold the center support so that the mattress doesn’t sag.
5. ASSEMBLY – ATTACH THE MATTRESS BOX TO THE LEGS
Bring the mattress box into the room and attach it to the 4×4 legs. This is where we used the carriage bolts, flat washers, split locking washers, and cap nuts. We pre-drilled the holes into the 4×4 legs and 2×6 mattress box, then inserted the carriage bolts, washers, and cap nuts. You’ll see where I had to carve out a space in the adjacent boards for the cap nuts. If you place your hardware further inward, you shouldn’t have this problem.
Once the mattress box is in place, you can measure and cut the 1×3 mattress slats and lay them in place. I spaced them about 5 1/2 inches apart (I used a scrap tongue-and-groove board as a spacer) and screwed them down with 1 1/4-inch wood screws. Be sure to pre-drill pilot holes so that you minimize the risk of the wood splitting.
This is also a good time to put the full-size mattress in – once you have all the walls attached, it’ll be a tough job to wrestle the mattress inside.
6. BUILD THE STAIRS
After hemming and hawing over whether to build stairs or a ladder, I finally decided to build stairs. I used 1×8 boards for this, which is plenty strong for the kiddos, but I feel a little uneasy when my husband puts his weight on these stairs. You may want to use 2×8 boards if you have trust issues like I do.
7. BUILD THE DOORS
I used leftover scrap tongue-and-groove boards and 1×3 mattress slats to build the doors. Measure, mark, and cut the T&G boards to length, plank them together, then attach the 1×3 boards on top with glue and nails. Simple enough. I used Varathane’s Golden Oak wood stain for the barn doors. Below, you’ll find a couple helpful videos on my staining and finishing process.
Installing the sliding barn door hardware was very straight-forward. The instructions that came with it were very easy to follow. Remember, the hardware set includes 2 hangers, so you’ll need to order 2 more because you need 4 total – 2 for each door. We did have to cut the metal rail down from 96 inches to 79 inches – we used an angle grinder for this, then used a file to remove any burrs and sharp edges and touched up the edges with black spray paint. We screwed the top mount hangers onto the doors, positioned and tightened the door stoppers, then hung the doors.
8. CUT THE ROOF PANELS AND ATTACH THE ROOF
Because this DIY sliding barn door loft bed already weighs a ton, I didn’t want to add too much more weight with the roof. I considered real shingles (too messy and gravelly), cedar shingles (not available in-store), plywood (more weight)… you name it, I probably considered it. I finally decided on these polycarbonate corrugated roof panels. They’re super light and come in different colors – you may even choose the translucent roof panels, if you want more light to come through. We chose the 8-foot panels in Castle Grey and used battery-powered RYOBI shears to cut it. You can also use a circular saw or even some heavy duty kitchen shears – the panels are plastic, so they’re super light and easy to work with.
We used these wood screws with foam washers to attach the roof panels to the rafters.
I kind of wish I would have either stained or painted these rafters. Oh, well. Hindsight is 20/20, isn’t it?
We also switched out the existing ceiling fan for this pretty flush mount light fixture. Isn’t it perfect?!
So… are you ready to build your own DIY Sliding Barn Door Loft Bed? I’ve got you covered with the plans! Hope you enjoy them – feel free to reach out if you have any questions along the way and please tag me on social media if you build this bed – I’d LOVE to see your versions! Happy building!
SHOP THIS POST
*This project is sponsored by The Home Depot. This post contains affiliate links. All expressed opinions and experiences are my own words. My post complies with the Word Of Mouth Marketing Association (WOMMA) Ethics Code and applicable Federal Trade Commission guidelines.
Brian Famous says
Oh my, the barndoors are an adorable concept. My son has wanted a loft bed for over a year, and I’m certain he’d love the idea of having sliding doors on the loft too!
Hayley says
What size is this room, just so I can get a better idea of whether or not it will fit well in my kids room?
Brandi says
Love this!! We’re gonna build it for our 10 year old daughter in our new home. Do you know the total length and width? Trying to make sure it’ll fit in the her room. Our ceilings will be 9.5’ so I know that part will be fine. Also, how on earth do you change the sheets? Lol
Jen says
Hi Brandi,
The dimensions are 86″w x 56″d x 96″h. I posted a video on my Instagram stories highlights, showing how I change the sheets. Check out the “DIY Loft Bed” highlight. Hope that helps!
Megg says
We just built this and getting it all together! Love it! Where did you get the handles for the doors at? I’ve searched and haven’t had any luck. Thanks!
Jen says
So awesome to hear, Megg! I had these pulls from a previous project, but I found a bunch of similar ones here: https://homedepot.sjv.io/c/1241677/456723/8154?u=https%3A%2F%2Fwww.homedepot.com%2Fs%2Fappliance%252520pulls%3FNCNI-5 Hope that helps!
Kady says
My local hardware stores don’t carry those roof panels. Would steel roof panels be too heavy? Would I be better off with plywood?
Brandi says
We are in the finishing stages of completing this bed and now the blueprints have disappeared and are saying we need to pay $20……literally at the stage of putting it together and having a few measurement issues and now no blueprints…..
Jen says
Hi Brandi,
Yes, the plans were available for free for several months and are now available for purchase on Spruc’d. An email of the plans should have been sent to whatever email you provided when you requested them.
Brandi says
The plans were sent but now it just takes me to the 404 error page and I can’t see the blueprints without purchasing.
Jen says
Brandi,
What email did you use to request the plans?
Claire says
About how many hours did you put into building this?
Vance lebeda says
How many hours did you have in building this?
Emily says
Do you have same plans but for a twin size??
Thank you
Jen says
Not at the moment, but maybe I should draw them up because I’ve gotten several requests!
Jennifer Moreland says
I’m planning to purchase the plans for this but I wanted to confirm first. Do you provide recommendations on modifying this for 8’ ceilings?
Sara says
Also here to hop on the twin size train. Please please PLEASE do a twin size. My little guy would love this as his first real bed. I’ve been planning on making the cabin bed but I love the doors on this and the ability to play underneath.
Jen says
Hi Sara,
Re: twin size sliding barn door loft bed – I’ll put it on my To Do list!
Emma Wilson says
Hi where can you get one of these I what a double bed of these so where can you get one from Emma
Robert says
What color white painted Did you use and stain for the doors. Bought the plans and on the last step but wife asked me to see what colors you used. Thanks again
Jen says
Hi Robert,
Thanks for your note! I used Benjamin Moore’s Simply White and Varathane’s Golden Oak stain on the doors. Hope that helps!
Nancy says
Can you easily add a full size bed to the underneath part instead of a sitting area? Do the plans reflect that option?
Jen says
Hi Nancy,
No, the plans don’t include a bed underneath, but it would be an easy modification! In fact, I’ve seen a few of my readers convert this loft bed to a bunk bed!
Kevin says
The lowest cost for a sliding door kit I found was 82 dollars and you need two. A bit pricey; any other sources?
Jen says
Hi Kevin,
I think you may be able to find them cheaper on Amazon. Good luck!
Kate says
OMG WHAT? I am obsessed with this! This is so incredible, thank you for sharing the plans!! Maybe I can get my hubby interested in helping 🙂
Maria says
I’d love to see this as a bunk bed as well! Where can we see brag posts from other readers who have built this?
Thanks!
Jen says
Hi Maria,
You can search the hashtag #jenwoodhouse on Instagram and see reader builds!
Kerry Watts says
I’ve purchased the plans for the loft barn door bed but seemed to have lost the cut list and recommended tools… anyway you can resend that? [email protected]
Jen says
Hi Kerry,
Sure thing! I just re-sent them via email. Thanks!
Steve says
I am going to purchase the plans for this bed but we only have 8 foot ceilings. Can it be modified to fit in a room with 8 foot ceilings?
Jen says
Hi Steve,
The top of the roof is 8 feet tall. You could modify it so that the legs are shorter, but keep in mind, this will decrease the head space under the loft bed. Hope that helps!
Laura says
So adorable!!! I’d love plans for this as twin bunk beds!
Penny Jackson says
Building the loft bed for our granddaughters. Working on the ladder. What angle did you cut the top of the 1 x 8 to make it flush against the mattress box?
Jen says
Hi Penny,
Great to hear! I hope your granddaughters love it! The bottom of the stairs are cut at a 25º angle and a right angle at the top. I’d recommend cutting the bottom edge of the 1×8 first, then hold the board in place up against the bed, trace the mark and cut the boards to fit. Hope that helps!
Nikki says
Love this! Side note. Where did you purchase the cute chairs underneath.